NTPC Management Trainee (MT) Syllabus 2024 | Exam Pattern, PDF Download
✨NTPC Management Trainee (MT) Syllabus 2024
The NTPC Management Trainee Exam 2024 is an online exam that will be conducted in an objective (MCQ) format. The exam will be available in both Hindi and English. There will be a total of 100 questions, each carrying one mark. The time allotted for the exam is 120 minutes.
The subjects for the exam will be based on the relevant diploma trade. The exam will consist of a single paper (Paper 1) with 100 questions and a maximum score of 100. The cutoff marks for the exam are as follows: General and EWS candidates must score at least 40%, while OBC, SC, and ST candidates must score a minimum of 30%. Check the full details of the NTPC Management Trainee (MT) Syllabus 2024 & Download the PDF from the quick link sections.
✨Key highlights to help students crack the exam in 2024:
-
Be well-prepared in your respective diploma trade subjects.
-
Practice MCQs and take mock exams.
-
Learn time management techniques.
-
Stay positive and focused.
NTPC MT SELECTION PROCESS
Online Exam
Document Verifications
★ Get the NTPC Management Trainee (MT) Syllabus 2024 PDF and Exam Pattern below.
NTPC MT Syllabus 2024 (CBT Exam, Stage 1)
NTPC MT Syllabus 2024 - Stage 2 Exam
The NTPC MT Syllabus 2024 for the Stage 1 CBT Exam is a challenging opportunity for people who want to become Management Trainees. The selection ratio is tough at 1 in 10, which shows how competitive it is. This online exam is at the 12th (Intermediate) level and has objective-type questions in both Hindi and English. Candidates have 120 minutes to complete the test, which has 120 questions worth a total of 90 marks.
Accuracy is important because correct answers get 0.75 marks, but there is a 0.25 mark penalty for incorrect answers. The cut-off marks differ by category. Stage 1 has three subjects: General English, Reasoning Aptitude, and Quantitative Aptitude, each with 40 questions and 30 marks. Students must study hard to do well in this very competitive exam.
Selection Ratio
1:10
Organization
NTPC
Exam Mode
Online (CBT)
Exam Level
12th (Intermediate)
Exam Type
Objective (MCQ)
Paper Medium
Hindi & English (Except language subject)
Total Question
120
Total Marks
90
Total Time (Minutes)
120
Correct Answer (Marks)
0.75
Negative Marking
0.25
Cut Off Marks
Paper
Stage 1
Subject Details
1. 📖General English
Vocabulary:
-
Synonyms and Antonyms
-
Homonyms, Homophones, and Homographs
-
One-Word Substitutions
-
Idioms and Phrases
-
Phrasal Verbs
-
Analogy
-
Vocabulary Building Strategies
Grammar:
-
Parts of Speech
-
Tenses
-
Articles
-
Prepositions
-
Conjunctions
-
Verbals (Gerunds, Participles, Infinitives)
-
Voice and Narration
-
Sentence Structure
-
Error Correction
2. 📖Reasoning aptitude
Verbal Reasoning:
-
Analogy and Classification
-
Similarities and Differences
-
Coding and Decoding
-
Number Series
-
Letter Series
-
Symbol Series
-
Analogy-Based Questions
-
Blood Relations
-
Directions and Distance
-
Time and Calendar
Non-Verbal Reasoning:
-
Figure Matrix
-
Figure Completion
-
Pattern Completion
-
Analogy-Based Questions
-
Spatial Ability
-
Visual Reasoning
-
Observation and Reasoning
3. 📖Quantitative aptitude
Numbers:
-
Number systems (fraction, decimal, Roman)
-
HCF and LCM
-
Divisibility rules
-
Powers and roots
-
Factorization
-
BODMAS rule
Algebra:
-
Linear equations and inequalities
-
Quadratic equations
-
Polynomials
-
Logarithms
Ratios and Proportions:
-
Ratio and proportion concepts
-
Direct and inverse proportions
-
Applications of ratios and proportions
Percentage:
-
Percentage concepts
-
Conversions between percentages, decimals, and fractions
-
Applications of percentages
Average:
-
Mean
-
Median
-
Mode
-
Weighted average
-
Moving average
Profit and Loss:
-
Profit and loss concepts
-
Cost price
-
Selling price
-
Profit percentage
-
Loss percentage
-
Discount
Simple Interest and Compound Interest:
-
Simple interest concepts
-
Compound interest concepts
-
Applications of simple and compound interest
Time and Distance:
-
Speed, time, and distance concepts
-
Relative speed
-
Average speed
-
Applications of time and distance concepts
Data Interpretation:
-
Data interpretation concepts
-
Tables
-
Graphs
-
Charts
-
Data sufficiency
Geometry:
-
Basic geometry concepts
-
Area
-
Perimeter
-
Volume
-
Pythagoras theorem
NTPC MT Syllabus 2024 (CBT Exam, Stage 2)
NTPC MT Syllabus 2024 - Stage 2 Exam
NTPC will conduct Stage 2 CBT (Computer Based Test) for Management Trainee (MT) in 2024. This test is for diploma holders and will be held online. The paper will be bilingual and will have 120 objective-type questions for 120 marks. Each correct answer will get one mark. The application deadline is April 24, 2023.
The cut-off marks are the same as Stage 1 and vary by category. Stage 2 will focus on specialized subjects like Electrical Engineering, Mechanical Engineering, and Control and Instrumentation. Each subject will have 120 questions. Candidates must prepare well for this advanced test.
Organization
NTPC
Exam Mode
Online (CBT)
Exam Level
Diploma
Exam Type
Objective (MCQ)
Paper Medium
Hindi & English (Except language subject)
Total Question
120
Total Marks
120
Total Time (Minutes)
120
Correct Answer (Marks)
01
Cut Off Marks
Paper
Stage 2
Subject Details
1. 📖Electrical Engineering
Electrical Fundamentals:
-
Basic concepts of electricity, such as voltage, current, resistance, power, and energy
-
AC and DC circuits
-
Network theorems, such as Kirchhoff's laws, Thevenin's theorem, and Norton's theorem
-
Electromagnetism and magnetic circuits
-
Transformers
-
Induction motors
Electrical Machines:
-
DC machines, including generators and motors
-
AC machines, including synchronous machines and induction machines
-
Single-phase and three-phase systems
-
Power factor and power factor correction
Electronic Devices and Circuits:
-
Semiconductor devices, such as diodes, transistors, and integrated circuits
-
Digital electronics
-
Operational amplifiers
-
Electronic communication systems
Control Systems:
-
Basic concepts of control systems, such as feedback, stability, and response time
-
Block diagrams and transfer functions
-
PID controllers
-
State-space analysis
Power Systems:
-
Power generation, transmission, and distribution
-
Power system analysis, including load flow and fault analysis
-
Protective relaying
Instrumentation and Measurement:
-
Basic concepts of measurement, such as accuracy, precision, and resolution
-
Transducers and instrumentation amplifiers
-
Data acquisition systems
-
Digital signal processing
2. 📖Mechanical Engineering
Applied Mechanics:
-
Force, work, energy, and power
-
Laws of motion and friction
-
Simple machines
-
Centroids and moments of inertia
-
Kinematics and kinetics of rigid bodies
-
Stress and strain
-
Bending and shear stresses
-
Torsional stress
Engineering Materials:
-
Properties of materials
-
Ferrous and non-ferrous metals
-
Polymers and composites
-
Heat treatment of steels
-
Mechanical testing of materials
Machine Design:
-
Design of machine elements
-
Gears, bearings, and couplings
-
Springs and brakes
-
Belts, pulleys, and chains
-
Machine tools
-
Power transmission
Thermal Engineering:
-
Thermodynamics
-
Heat transfer
-
Fluid mechanics
-
Internal combustion engines
-
Refrigeration and air conditioning
-
Power plant engineering
Production Engineering:
-
Manufacturing processes
-
Metal forming and casting
-
Welding and joining
-
Metrology and quality control
-
Production planning and control
Engineering Drawing:
-
Orthographic projection
-
Isometric projection
-
Sections and intersections
-
Dimensions and tolerances
-
Assembly drawings
Electrical and Electronics Engineering:
-
Basic electrical concepts
-
DC circuits
-
AC circuits
-
Transformers and motors
-
Electronic devices and circuits
-
Digital electronics
Instrumentation and Control:
-
Measurement of mechanical and electrical parameters
-
Control systems
-
Data acquisition and processing
-
Industrial automation
3. 📖Control and Instrumentation
Fundamentals of Control and Instrumentation:
-
Basic concepts of control systems
-
Block diagram representation of control systems
-
Transfer functions and frequency response
-
Stability analysis of control systems
-
Introduction to feedback control systems
Process Control:
-
Process modeling and simulation
-
Process control instrumentation
-
PID controllers
-
Advanced control strategies
-
Process monitoring and fault detection
Instrumentation:
-
Sensors and transducers
-
Signal conditioning
-
Data acquisition and transmission
-
Industrial control systems
-
Programmable logic controllers (PLCs)
Applications of Control and Instrumentation:
-
Process control in industries such as chemical, petrochemical, and power generation
-
HVAC control systems
-
Robotics and automation
-
Biomedical instrumentation
This syllabus is designed based on the previous year's NTPC MT Exam. A new syllabus will be released soon.
Important Links | |
---|---|
Download Syllabus PDF | Click Here |
Free Online Test Series | Click Here |
Download App [ For Latest Updates Download Our Andriod App ] | CLICK HERE |
NTPC Management Trainee Syllabus 2024 FAQ
⭐Q: What is the NTPC MT Selection Process?A: The NTPC MT selection process consists of two stages: Stage 1: Computer-based test (CBT) with subjects like General English, Reasoning Aptitude, and Quantitative Aptitude. Stage 2: Specialized CBT with subjects like Electrical Engineering, Mechanical Engineering, and Control and Instrumentation.
⭐Q: What is the time duration for the NTPC MT Stage 1 and Stage 2 exams?A: Both stages are 120 minutes long. Candidates are allotted 120 minutes to complete the examination.
⭐Q: Are there any language restrictions in the NTPC MT exams?A: The exams are bilingual, available in both Hindi and English. However, this does not apply to language-specific subjects, which may be available only in one language.
⭐Q: How is the NTPC MT exam marked, and is there a negative marking scheme?A: Stage 1: Correct answers are awarded 0.75 marks. There is a negative marking scheme of 0.25 marks for each incorrect answer. Stage 2: Each correct answer is worth 1 mark.
⭐Q: What are the cut-off marks for the NTPC MT exam, and do they vary by category?A: Yes, cut-off marks vary by category. Stage 1 cut-offs: General: 40%, EWS: 40%, OBC: 30%, SC: 30%, and ST: 30%. Stage 2 cut-offs are based on Stage 1 performance
Comments-
Updated:
Highlights
Advertisements
Comment