1/60

(1) Which is not part of a file? | कौन एक फाइल का हिस्सा नहीं है? PSUs-2018


(2) The file used for filing leather is _______ | चमड़ा फाइल करने के लिए प्रयुक्त फाइल _______ है PSUs-2019


(3) One micron=-________Cm | एक माइक्रोन=-________सेमीPSUs-2020


(4) What is the point angle of the prick punch which is used for making light punch marks? | प्रिक पंच का बिंदु कोण क्या है जिसका उपयोग हल्के पंच चिह्न बनाने के लिए किया जाता है?PSUs-2019


(5) The engineer's hammer is specified by its_____________ | इंजीनियर के हथौड़े को इसके _________ द्वारा निर्दिष्ट किया जाता है PSUs-2019


(6) If the strength of the material to be drilled is high, the drill speed should be - | यदि ड्रिल की जाने वाली सामग्री की ताकत अधिक हो, तो ड्रिल की गति होनी चाहिए - PSUs-2018


(7) Calculate the spindle RPM for a drilling speed of 44 m/min and diameter of drill 20mm, | 44 मीटर/मिनट की ड्रिलिंग गति और ड्रिल 20 मिमी के व्यास के लिए धुरी आरपीएम की गणना करें,PSUs-2020


(8) What is the coolant used for machining cast iron?| कच्चा लोहा मशीनिंग के लिए उपयोग किया जाने वाला शीतलक क्या है? PSUs-2019


(9) In a vernier caliper, 39 main scale divisions are divided into 40 equal points on the vernier scale. Then what is its least count (LC) in mm? (take the value of the main scale division=lmm) | वर्नियर कैलीपर में, 39 मुख्य स्केल डिवीजनों को वर्नियर स्केल पर 40 बराबर बिंदुओं में विभाजित किया जाता है। तो मिमी में इसकी अल्पतमांक (LC) क्या है? (मुख्य स्केलडिवीजन का मान लें = lmm)PSUs-2019


(10) As per the Indian standard (IS) system, a drill bit is designated as 9.5-H-IS5101-HS, in this the number 9.5 stands for.| भारतीय मानक (IS) प्रणाली के अनुसार, एक ड्रिल बिट को 9.5-H-IS5101-HS के रूप में नामित किया गया है, इसमें संख्या 9.5 है। PSUs-2018


(11) The angle 60° 45'=_________ | कोण 60° 45'=_________PSUs-2018


(12) The diameter of the thread, at which the thread thickness equal to half of the pitch is called | धागे का व्यास, जिस पर धागे की मोटाई पिच के आधे के बराबर होती है, कहलाती है PSUs-2019


(13) The least count of vernier bevel protractor is | वर्नियर बेवल प्रोट्रैक्टर का अल्पतमांक हैPSUs-2018


(14) In a screw thread, the top surface joining two adjacent sides of the thread is called | एक पेंच धागे में, धागे की दो आसन्न भुजाओं को मिलाने वाली शीर्ष सतह कहलाती है PSUs-2019


(15) What is the blank size (diameter) for preparing a bolt of M12X1.5? | M12X1.5 का बोल्ट तैयार करने के लिए रिक्त आकार (व्यास) क्या है?PSUs-2020


(16) Which vice is used for holding rivets, and keys?| रिवेट्स और चाबियों को रखने के लिए किस वाइस का उपयोग किया जाता है? PSUs-2018


(17) A single tool that performs the combined operation of drilling and counter sinking is called | एक एकल उपकरण जो ड्रिलिंग और काउंटर सिंकिंग का संयुक्त संचालन करता है, कहलाता है PSUs-2018


(18) In a tolerance system, as per the below figure, the dimension 'x' represents -| एक सहिष्णुता प्रणाली में, नीचे दिए गए चित्र के अनुसार, आयाम 'x' दर्शाता है - PSUs-2019


(19) In a hole and shaft tolerance system, a small letter indicates the fundamental deviation of | एक छेद और शाफ्ट सहिष्णुता प्रणाली में, एक छोटा अक्षर PSUs-2020


(20) If tolerance of hole and shaft is represented as shown below the figure, then this fit is called| यदि छेद और शाफ्ट की सहनशीलता को चित्र के नीचे दिखाया गया है, तो इस फिट को कहा जाता है PSUs-2019


(21) A pneumatic drill is operated by| न्यूमेटिक ड्रिल किसके द्वारा संचालित होती है PSUs-2019


(22) Find out the distance between the two holes in a plate as per the hole table shown below figure, | एक प्लेट में दो छेदों के बीच की दूरी नीचे दिए गए चित्र में दिखाए गए छेद तालिका के अनुसार ज्ञात कीजिए,PSUs-2020


(23) What is an angle 'Ø' represented in the cutting tool figure given below?| नीचे दिए गए कटिंग टूल में दिए गए कोण 'Ø' को क्या कहते हैं? PSUs-2019


(24) As the rake angle of the cutting tool reduces, its strength will_______ | जैसे-जैसे कटिंग टूल का रेक एंगल कम होता जाएगा, उसकी ताकत _______ होगी PSUs-2020


(25) Identify the heaviest material in the given options. | दिए गए विकल्पों में से सबसे भारी सामग्री को पहचानें। PSUs-2020


(26) Name the part of a lathe machine, that provides the method of holding and moving the cutting tool, | एक लेथ मशीन के उस भाग का नाम बताइए, जो काटने के उपकरण को पकड़ने और हिलाने की विधि प्रदान करता है, PSUs-2019


(27) The process of obtaining pig iron from iron ore is called________ | लौह अयस्क से कच्चा लोहा प्राप्त करने की प्रक्रिया को ________ कहा जाता है PSUs-2019


(28) What is the purity level of wrought iron? | गढ़ा लोहे का शुद्धता स्तर क्या है?PSUs-2019


(29) As the % of carbon increases in iron, it becomes more________ | जैसे-जैसे लोहे में कार्बन का प्रतिशत बढ़ता है, यह अधिक हो जाता है________ PSUs-2019


(30) Epoxy is a_________ | एपॉक्सी एक ________ है PSUs-2018


(31) The material used in furnace walls as an innermost layer, to resist high temperatures, and physical and chemical reactions is called- | उच्च तापमान, और भौतिक और रासायनिक प्रतिक्रियाओं का विरोध करने के लिए भट्ठी की दीवारों में एक अंतरतम परत के रूप में प्रयुक्त सामग्री को कहा जाता है- PSUs-2020


(32) The forging process in which, the length of the forge reduces and cross-section increases is called | फोर्जिंग प्रक्रिया जिसमें फोर्ज की लंबाई कम हो जाती है और क्रॉस-सेक्शन बढ़ जाता है, कहलाता है PSUs-2018


(33) The process of stiffening the edge of sheet metal article by folding is called__________| शीट धातु की वस्तु के किनारों को मोड़कर सख्त करने की प्रक्रिया को __________ कहा जाता है PSUs-2020


(34) Find out the outer surface area of the hollow thin cylinder, whose diameter is 7 cm and whose length is 10 cm. | खोखले पतले बेलन का बाहरी पृष्ठीय क्षेत्रफल ज्ञात कीजिए, जिसका व्यास 7 सेमी और लंबाई 10 सेमी है। |PSUs-2019


(35) What is the color code of the acetylene cylinder in oxy-acetylene gas welding?| ऑक्सी-एसिटिलीन गैस वेल्डिंग में एसिटिलीन सिलेंडर का रंग कोड क्या होता है? PSUs-2019


(36) What is the unit of Torque? | टॉर्क की इकाई क्या है? PSUs-2019


(37) What is the full form of LPG? | एलपीजी का फुल फॉर्म क्या है? PSUs-2019


(38) What is the welding rod used for welding aluminum plates?| एल्युमिनियम प्लेट की वेल्डिंग के लिए किस वेल्डिंग रॉड का उपयोग किया जाता है? PSUs-2018


(39) Convert 104° F into Degree Celsius, | 104° F को डिग्री सेल्सियस में बदलें,PSUs-2020


(40) What is the welding symbol for fillet weld? | पट्टिका वेल्ड के लिए वेल्डिंग प्रतीक क्या है?PSUs-2019


(41) What is the smaller diameter of a tapered pin shown below figure? | नीचे दी गई आकृति में दिखाए गए टेपर्ड पिन का छोटा व्यास कितना है?PSUs-2020


(42) In an electroplating process, the item to be coated is used_________ | इलेक्ट्रोप्लेटिंग प्रक्रिया में, लेपित की जाने वाली वस्तु का उपयोग किया जाता है_________ PSUs-2019


(43) Pick the material which has the least coefficient of thermal expansion, | वह सामग्री चुनें जिसमें थर्मल विस्तार का सबसे कम गुणांक हो, PSUs-2020


(44) If the rod is bent into a curved shape as shown below the figure, then the top most layer is subjected to| यदि छड़ को वक्र आकार में मोड़ा जाता है जैसा कि आकृति के नीचे दिखाया गया है, तो सबसे ऊपरी परत के अधीन होता है PSUs-2019


(45) What is the relation between the lead (L) and pitch (P) of a two-start thread screw? | टू-स्टार्ट थ्रेड स्क्रू के लीड (L) और पिच (P) के बीच क्या संबंध है? PSUs-2020


(46) Identify a solid lubricanť'? | एक ठोस स्नेहक की पहचान करें'? PSUs-2019


(47) In which machining process, a large amount of material is removed? | किस मशीनिंग प्रक्रिया में बड़ी मात्रा में सामग्री को हटा दिया जाता है? PSU-2019


(48) Name the fit, in which the shaft is cooled below room temperature until it fits into the hole, then the assembly is allowed to attain room temperature.| उस फिट का नाम बताइए, जिसमें शाफ्ट को कमरे के तापमान से नीचे तब तक ठंडा किया जाता है जब तक कि वह छेद में फिट न हो जाए, फिर असेंबली को कमरे का तापमान प्राप्त करने की अनुमति दी जाती है। PSU-2019


(49) Pick the non-conventional machining method; it uses a reverse metal plating process. | गैर-पारंपरिक मशीनिंग विधि चुनें; यह एक रिवर्स मेटल प्लेटिंग प्रक्रिया का उपयोग करता है। PSU-2019


(50) Name the tool, which is used to lift or move heavy loads by leverage effect.| उस उपकरण का नाम बताइए, जिसका उपयोग उत्तोलन प्रभाव द्वारा भारी भार को उठाने या स्थानांतरित करने के लिए किया जाता है। PSU-2019


(51) In a machine maintenance manual, regarding the frequency of lubricating the machine, the square symbol represents--- | मशीन रखरखाव नियमावली में, मशीन को लुब्रिकेट करने की आवृत्ति के संबंध में, एक वर्गाकार प्रतीक ---- PSU-2019


(52) How many cubes of 4mm side can be cut from a cube of side 8mm? | 8 मिमी भुजा वाले घन से 4 मिमी भुजा वाले कितने घन काटे जा सकते हैं?PSU-2019


(53) The product of two quantities A and B is (25x-4), IfA=(5x -2), Then find B? | दो मात्राओं A और B का गुणनफल (25x-4) है, यदि A=(5x -2), तो B ज्ञात कीजिए?PSU-2019


(54) A spherical aluminum ball is melted and made into smaller balls of 1/3 d radius of the original one. Then how many such balls can be made? | एक गोलाकार एल्युमिनियम की गेंद को पिघलाया जाता है और मूल गेंद के 1/3 d त्रिज्या की छोटी गेंदों में बनाया जाता है। तो ऐसी कितनी गेंदें बनाई जा सकती हैं?PSU-2018


(55) An alloy of weight 63kg is made up of Copper, Zinc, and Tin metals by mixing in the ratio of 4:3:2 respectively Then pick the correct weights (kg) of each metal in this allow in the same order. | 63 किलो वजन का एक मिश्र धातु क्रमशः 4:3:2 के अनुपात में मिलाकर कॉपर, जिंक और टिन धातुओं से बना है, फिर उसी क्रम में प्रत्येक धातु का सही वजन (किलो) चुनें।PSU-2019


(56) The weight of 75 m volume of metal is 150 gm. Then find the weight of 300 m volume of the same metal, | धातु के 75 मीटर आयतन का भार 150 ग्राम है। तो उसी धातु के 300 मीटर आयतन का भार ज्ञात कीजिए,PSU-2020


(57) The friction force exerted by the air on a moving body is called________| गतिमान पिंड पर हवा द्वारा लगाए गए घर्षण बल को ________ कहा जाता है PSU-2018


(58) A force of 30ON is applied at the end of the spanner, whose effective length is 15cm. Then find the torque applied. | स्पैनर के अंत में 30ON का बल लगाया जाता है, जिसकी प्रभावी लंबाई 15cm है। तब लगाया गया बलाघूर्ण ज्ञात कीजिए।PSU-2019


(59) What is Young's modulus of mild steel? | माइल्ड स्टील का यंग मापांक क्या है?PSU-2020


(60) Where is the center of gravity (CG) of a right circular cone of height, from the base? | ऊंचाई के एक लम्ब वृत्तीय शंकु का गुरुत्व केंद्र (CG) आधार से कहाँ है?PSU-2020